#09 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

HALDEX USB CAN DONGLE DRIVERS PC

HALDEX USB CAN DONGLE DRIVER DETAILS:

Type: Driver
File Name: haldex_usb_40047.zip
File Size: 3.7 MB
Rating:
4.38
53 (4.38)
Downloads: 35
Supported systems: Windows XP (32/64-bit), Windows Vista, Windows 7, Windows 8.1, Windows 10
Price: Free* (*Free Registration Required)

Download Now
HALDEX USB CAN DONGLE DRIVER



Have a question or need an advice?

HALDEX USB CAN DONGLE DOWNLOAD DRIVER

Uses ELM adapter. TIS Techstream V EcuVonix 3. Buying Format see all. All Listings Accepts Offers While the ECU is powered, information is transferred to the Info Centres memory, which can be recalled. Power is supplied from the vehicle system via the ECU diagnostics connector. For further information refer to the Info Centre 2 user guide Distance Odometer - total distance Trip distance 1st and 2nd Service haldex usb can dongle Wheel scale factor Clock time and date Clear trip 1 and 2 Alternatively - directly connected to ECU or side-of-vehicle connection. This also allows configuration with system parameters to be entered and an end-of-line test to be carried out. As an option to the cab warning device a trailer mounted warning lamp may be provided as an auxiliary function. This lamp mimics the signal to the cab warning device but will only function if the ISO power is connected.

The signal produced by the trailer warning lamp may be different to that produced by the cab device due to possible modification of the cab device by the towing vehicle. System check procedure 1.

On power up of the system, the warning device must indicate haldex usb can dongle of the following sequences in order to show a fault free system: Option A Option B 2. During the self-check procedure, the system cycles the EPRVs. With foot brake applied one exhaust of air from each EPRV will be audible.

VAG COM

Once these two checks are made with correct results, no further checks are required. The system adopts load sensing mode when the brakes are applied.

HALDEX USB CAN DONGLE WINDOWS 8 DRIVER

This load sensing mode is limited to 2 minutes for any single brake application, after which it returns to a push-through condition approx With yellow line pneumatic pressure i. Brakes On, park on air.

Apply foot brake, switch Ignition On. The system adopts a push-through approx condition.

DRIVERS UPDATE: HALDEX USB CAN DONGLE

When the brakes are released and re-applied the system remains in push-through unless the brakes are released for longer than 2 minutes, after which it returns to load sensing operation. Pin 1 1 Pin. Correct value 0.

Diagnostic trouble codes DTC If a diagnostic trouble code displayed is not listed here, check for intermittent sensor and wiring faults. Possible causes No supply on ignition switched line. Damaged exciter.

Security Check

Maladjusted sensor or worn sensor cable insulation. Modulator 21 hold solenoid short circuit Modulator 21 dump solenoid short circuit Modulator 21 hold solenoid open circuit Modulator 21 dump solenoid open circuit Modulator 21 hold solenoid short circuit permanently energised Modulator 21 dump solenoid short circuit permanently energised Modulator 21 hold solenoid control circuit fault Modulator 21 dump solenoid control circuit fault Slow recovery of one wheel of modulator 21 Slow recovery of one wheel of modulator 22 Slow brake release, foundation haldex usb can dongle mechanical faults, dry bearings, broken spring, restricted piping. Check for kinks and blockages etc.

Utilizing serial communication, this device haldex usb can dongle able to record over data channels with a frequency of 25Hz. Use [ See what we offer in training seminars and on-site training. The EMU Black is a class-leading, stand-alone engine management system, designed to operate the most advanced and complex engines available. It is a successor of our proven system, EMU. Little sealed bag help stop it getting wet if it is that.Diagnostics via ISO CAN supported by EB+ since 05/ from ECU USB Interface ISO Interface Assembly or acts as a hardware dongle. The USB dongle software can be updated to the latest revision. When no ECU is connected, the DIAG+ software can be configured for any of the following.

Related Posts